@article { author = {Parsakhoom, Aidin and Mostafa, Mohsen,}, title = {The necessity of using large-scale field rainfall simulator to investigate soil erosion and interception}, journal = {Extension and Development of Watershed Management}, volume = {8}, number = {30}, pages = {19-26}, year = {2020}, publisher = {Watershed Management Society of Iran}, issn = {2645-4777}, eissn = {}, doi = {}, abstract = {Due to the logistical challenges of large-scale rainfall simulator, most studies to date have used small scale rainfall simulator with a nozzle height of less than 3 m and a plot area of less than 5 m 2. Performing such small-scale studies is valuable for investigating the rate of soil erodibility, soil infiltration, the impact of herbaceous and shrub cover on water erosion and runoff. But there is a need for larger rainfall simulator to better understand and deepen the water cycle process and the interactions that occur on a larger scale. The rainfall simulator should be designed to simulate rain from top of canopy. In this case, raindrops can reach their final speed. For this purpose, a 15-meter anchored tower (controlling tower by several cable is called anchoring) with multiple nozzles is need. The most important component of any rainfall simulator is the type of nozzle used. The most common type of nozzle is a rotating plate nozzle with a 360 ° rotation angle in two linear mounting patterns and H mounted on top of the mast. The nozzles are connected vertically to a water tank and pump motor via a plastic pipe. After setting up the system and calibrating the rainwater, a windmill collector with a radius of 5 meters (about 80 m 2) of thick nylon, thin rods and zippers is used to collect throughfall, interception, and stemflow. In water erosion of soil, the most important stage that the soil is washed is rutting stage. In small-scale rainfall simulator, the low dimensions of plots causes runoff doesn’t have enough time to rut the soil, so in this condition true knowledge about soil erodibility cannot be achieved.   }, keywords = {Rainfall Simulator,nozzle,Anchoring,water erosion,Interception}, title_fa = {بررسی مروری انواع باران‌سازها و ضرورت استفاده از باران‌سازهای صحرایی بزرگ‌مقیاس برای بررسی فرسایش خاک و تاج بارش}, abstract_fa = {به‌دلیل چالش‌های لجستیکی باران‌سازهای بزرگ‌مقیاس، در اغلب مطالعاتی که تاکنون صورت پذیرفته از باران‌سازهای کوچک­مقیاس با ارتفاع نازل کم‌تر از 3 متر و سطح کرت کم‌تر از 5 مترمربع بهره گرفته شده است. اجرای این قبیل مطالعات کوچک­مقیاس برای بررسی مقدار فرسایش‌پذیری خاک، نفوذ خاک، تأثیر پوشش گیاهان علفی و بوته‌ای بر فرسایش آبی و رواناب بسیار ارزشمند می‌باشد، اما برای درک بهتر و عمیق‌تر فرایند چرخه آب و اثرات متقابلی که در مقیاس بزرگ‌تر حادث می‌شود نیاز به باران‌سازهای بزرگ‌تر را توجیه می‌کند. باران‌ساز باید طوری طراحی شود که بتواند باران را از ارتفاع بالای تاج پوشش شبیه‌سازی نماید، در این حالت قطرات باران نیز می‌توانند به سرعت نهایی خود برسند. بدین‌منظور یک دکل حداقل 15 متری لنگربندی (برای برپا نگه داشتن دکل باران‌ساز از کابل‌های مهار استفاده می‌شود که به این کار لنگربندی گفته می‌­شود) شده که امکان نصب چند نازل در رأس آن وجود داشته باشد نیاز است. مهم‌ترین جز هر باران‌ساز نوع نازلی است که به­‌کار می‌رود. معمول‌ترین نوع نازل، نازل صفحه‌ای چرخنده با زوایه دوران 360 درجه در دو الگوی نصب خطی و H می‌باشد که در رأس دکل نصب می‌شود. نازل‌ها از طریق یک لوله پلاستیکی به‌صورت عمودی به مخزن آب و موتور پمپ متصل می‌شوند. پس از راه‌اندازی سامانه و واسنجی باران‌ساز، از یک مخزن جمع­آوری­کننده بادبزنی به شعاع پنج متر (حدود 80 مترمربع) از جنس نایلون ضخیم، میله‌های نازک و بست برای جمع‌آوری ساقاب و تاج‌بارش استفاده می‌شود. در رابطه با فرسایش آبی خاک، مهم‌ترین مرحله­‌ای که در آن هدررفت خاک حادث می‌شود، مرحله شیاری شدن است. در باران­‌سازهای کوچک‌مقیاس، ابعاد کم کرت‌­ها مجال فرسایش شیاری را به رواناب نمی­‌دهد و لذا نمی­‌توان درک درستی از فرسایش‌­پذیری خاک داشت.}, keywords_fa = {شبیه‌سازی باران,نازل,لنگربندی,فرسایش آبی,تاج بارش}, url = {https://www.wmji.ir/article_254385.html}, eprint = {https://www.wmji.ir/article_254385_dc4c95eb581e53ee091dd5cc612036b0.pdf} }